Current issue
Archive
About the Journal
About
Editorial Board
Abstract & Indexing
Contact
Editorial Policies
Authorship & COI
Ethical principles
Principles of Transparent Checklist
Open access
For Authors
Instructions to Authors
Detailing Guidelines for Authors
Review process
Review sheet
How to submit
Open Access license
ORIGINAL PAPER
The impact of additives applied to the lubricant on the burnishing process and tribological properties
1
University of Zielona Gora, Institute of Mechanical Engineering, prof. Z. Szafrana 4, 65-516 Zielona Góra, POLAND
2
Faculty of Mechanical Engineering, Poznan University of Technology, Piotrowo 3 Street, 60-965 Poznan, POLAND
3
Mechanical Engineering Faculty, University of Slavonski Brod, Trg Ivane Brlic-Mazuranic 2, HR-35000 Slavonski Brod, CROATIA
Online publication date: 2023-06-28
Publication date: 2023-06-28
International Journal of Applied Mechanics and Engineering 2023;28(2):13-23
KEYWORDS
ABSTRACT
The aim of this study was to determine the impact of additions of tungsten carbide and silicon carbide microparticles to the lubricant used in the burnishing process on the tribological properties of friction pairs. The cylinders made of AISI 1045 steel constituted a workpiece. Burnishing was made with a lubricant the SN150 base oil with addition of tungsten carbide and silicon carbide microparticles. The tested materials were burnished with forces of 1000 N and 1500 N. Before and after the burnishing process, the surface roughness and hardness of the tested materials were measured. The study also presents the results of tribological properties of friction pairs with the tested structural materials. It was found that the addition of tungsten carbide microparticles to the base oil in the burnishing process can result in improved surface quality and reduced surface roughness. The results also confirmed the effect of addition of tungsten carbide and silicon carbide to the lubricant used in the burnishing process on tribological properties.
REFERENCES (15)
1.
Priyadarsini Ch., Venkata Ramana V.S.N., Aruna Prabha K. and Swetha S. (2019): A review on ball, roller, low plasticity burnishing process.– Materials Today: Proceedings. vol.18, pp.5087-5099.
2.
Raza A. and Kumar S. (2022): A critical review of tool design in burnishing process.– Tribology International, vol.174, pp.1-22.
3.
Rodriguez A., López de Lacalle L.N., Celaya A.,Lamikiz A. and Albizuri J. (2012): Surface improvement of shafts by the deep ball-burnishing technique.– Surface and Coatings Technology, vol.206, No.11-12 pp. 2817-2824.
4.
Low K.O. and Brevern P.V.(2009): On the surface and tribological characteristics of burnished cylindrical Al-6061.– Tribology International, vol.42, pp.320-326.
5.
Basak H. and Goktas H.H. (2009): Burnishing process on al-alloy and optimization of surface roughness and surface hardness by fuzzy logic.– Materials Design, vol.30, No.4, pp.1275-2181.
6.
Gharbi F., Sghaier S. and Benameur T. (2011): Effect of ball burnishing process on the surface quality and microstructure properties of AISI 1010 steel plates.– Journal of Materials Engineering and Performance, vol.20, pp.903-910.
7.
Lewandowski A., Laber S. and Jenek M. (2004): Evaluation of tribological properties of GJL-250 cast iron after burnishing treatment conditioned by the type of lubricant.- Tribology. vol.5, pp.137-144.
8.
Lewandowski A. (2013): Tribological properties of EN-GJSFP-500-7 cast iron burnished in the presence of operating preparations based on solid and chemical lubricants.- Tribology. vol.1, no.4, pp.67-84.
9.
Chodkiewicz A., Kaldoński T.(2020): Study of lubricating properties of mineral base oil containing hexagonal boron nitride nanoparticles and evaluation of the effect of surfactants on their sedimentation.- VAT Bulletin. vol.69,no. 4, pp.16-41.
10.
Spikes H. (2015): Friction modifier additives.– Tribology Letters. vol.60, No.1, pp.5-15.
11.
Alazemi A.A., Etacheri V., Dysart AD., Stacke LE. and Pol V.G. (2015): Ultrasmooth submicrometer carbon spheres as lubricant additives for friction and wear reduction.– ACS Applied Materials, vol.7, No.9, pp.5514-5521.
12.
Guegan J., Southby M.,Spikes H.(2019): Friction modifier additives, synergies and antagonisms.– Tribology Letters. vol.67, pp.1-12.
13.
Wu Y.Y., Tsui W.C. and Liu T.C. (2007): Experimental analysis of tribological properties of lubricating oils with nanoparticle additives.– Wear, vol.262, No.7-8, pp.819-825.
14.
Omrani E. Menezes P.L. and Rohatgi P.K.(2019): Effect of micro- and nano-sized carbonous solid lubricants as oil additives in nanofluid on tribological properties.– Lubricants, vol.7, No.3, pp.1-13.
15.
Krolczyk G.M., Nieslony P., Krolczyk J.B., Samardzic I., Legutko S., Hloch S., Barrans S. and Maruda R.W. (2015): Influence of argon pollution on the weld surface morphology.- Measurement, vol.70, pp.203-213.
| eISSN: | 2353-9003 |
| ISSN: | 1734-4492 |
Task: edition of a scientific journal, its internationalization and ensuring open access to the journal via the Internet
© 2006-2024 Journal hosting platform by Bentus
We process personal data collected when visiting the website. The function of obtaining information about users and their behavior is carried out by voluntarily entered information in forms and saving cookies in end devices. Data, including cookies, are used to provide services, improve the user experience and to analyze the traffic in accordance with the Privacy policy. Data are also collected and processed by Google Analytics tool (more).
You can change cookies settings in your browser. Restricted use of cookies in the browser configuration may affect some functionalities of the website.
You can change cookies settings in your browser. Restricted use of cookies in the browser configuration may affect some functionalities of the website.
